3-in-1 EMF Meter Detects Electric Field (EF), Radio Frequency Field (RF), Magnetic Field (MF) – for Home EMF Inspections, Office, Outdoor and Ghost Hunting, Smart Meters

Features:

👍 Measures and detects three types of EMF pollution: AC magnetic, AC electric,
and RF/microwave radiation.

👍 Large liquid-crystal display (LCD) and adjustable backlight for clear and precise reading.

👍 The audio sound feature assists you in locating the sources of EMFS.

👍 The Peak hold function assists in pinpointing digital EMF surces.

👍 Can measure both standard and weighted measurements. Special frequency weighted
mode for measuring electric current from EMF in the human body.

👍 Magnetic field strength is measured in milliGauss (mG) for 3 axis X, Y, and Z.
MF Mode covers 40 Hz – 100 kHz with range of 0.1 – 100.0 milligauss (mG).

👍 Electric field strength is measured in volt per meter (V/m). EF Mode covers
40 Hz – 100 kHz with range of 1 – 1000 volts per meter (V/m)

👍 RF field strength is measured in millivolt per meter (mW/m²). RF Mode covers
20 MHz – 6 GHz with range of 0.001 – 19.999 milliwatts per square meter (mW/m²).

👍 RF mode that is sensitive for gauging mobile phones and Wi-Fi EMF.
It can ddetect 5G signal and radio frequency up to 10Ghz.

👍 EMF Meter only, Battery is NOT included- 9V alkaline battery is required.

【The Standard Modes】

In standard modes for magnetic fields (MAG) and electric fields (ELEC), the field
measurement will measure fields using a flat frequency response.
The frequencies range from 40 Hz to 100 kHz, with equal sensitivity at 100 kHz.

【The Weighted Modes】

In weighted modes, the field measurement displays a proportional number corresponding
to the average electric current induced within the human body from
the fields. The number is equivalent to the amount of 60 Hz magnetic or
electric field that would be required to induce that amount of current.

【RF Modes】

To measure an RF field, adjust the knob to the RF setting and point the top of the
meter towards the potential source. Alternatively, you can simply hold
the meter vertically. The RF Mode uses the same plate sensor as the AC Electric Mode.

【The Peak Measurement】

The large numerals (at the bottom) show the field measurement in real time
and match the field percentage indicator graph.
The Peak Measurement (small numerals in the upper-left of the display) captures
the highest number and holds it for 5 seconds or until a higher number is
detected. For measuring magnetic and electric fields, the field measurement
numbers are effective. For cell phones, cell towers and wifi routers which
emit in pulses, the peak measurement numbers are more helpful.

【Frequently Questions and Answers】

Q: Do I measure on Standard or Weighted or both?

A: Both. Standard MAG or ELEC measures the intensity of the field without
taking frequency into consideration (40Hz-100kHz). Weighted MAG or
ELEC puts more emphasis on the frequencies above 60Hz. These higher
frequencies will generate more electric current in the human body. For
instance, at 60Hz, the body is exposed to field pulses 60 times per second,
whereas at 120Hz, the body is subjected to twice the number of pulses, or
120 times per second, even though the field remains the same.

Q: When to use MAG,ELEC or RF?

A: To determine when to use Magnetic (MAG), Electric (ELEC) or Radio (RF) fields,
it is important to understand the typical sources of each.

➤ MAG fields are usually emitted by motors, appliances, wiring and power lines.
➤ ELEC fields come from power lines, lights, wall outlets, electrical switches,
and ungrounded appliances.
➤ RF fields are often found near transmitting cell phones and wifi
routers, cell phone towers, microwave ovens, smart meters, wireless landline
phones or walkie talkies, and radio/tv stations.

Smart meters from power companies typically pulse once per minute, so watch for the
peak number. To reduce exposure, one should either avoid high-field areas
or use shielding, as each type of field has its own specific shielding techniques.

Q: What is considered a safe level?

A: There is no absolute safe level that has been established. However,
based on our research, there have not been any issues reported when staying below the following:

— 3mG Standard Magnetic or 5mG Weighted Magnetic
— 50 V/m Standard or Weighted Electric
— 0.200 mW/m² RF (field measurement) or 1.000 mW/m² (peak measurement)

These Exposure Levels are the typical readingstaken from homes and offices
that have relatively low total electromagnetic fields. The legal maximum
exposure levels are much higher than the levels mentioned above.
Some practitioners may suggest different levels.

【3 In 1 EMF Meter】PSB0H0 multi-field EMF Meter is a small and compact detector that can measure electromagnetic field (3-axis), electric field, and RF strength.
【Multi-Function】Sizeable LED display with adjust-able backlight for clear and precise reading, Displays signal level, peak level, and the fast indicator bar (for pulse monitoring). It could both measure standard and weighted (emphasizes high frequencies) measurements.
【Widely Used】This EMF measurement devices can be utilized for ghost-hunting, making it a must-have for anyone intrigued by paranormal phenomena. Additionally, it is also ideal for office workers, pregnant women, and the elderly who require detection of electrical radiation for their own health
【When to Use】MAG fields are usually emitted by motors, appliances, wiring and power lines. LEC fields come from power lines, lights, wall outlets, electrical switches, and ungrounded appliances. RF fields are often found near transmitting cell phones and wifi routers, cell phone towers, microwave ovens, smart meters, wireless landline phones or walkie talkies, and radio/tv stations.
【Display & Audio】 If you’re looking to accurately determine the actual EMF radiation levels of certain items, the field indicator is a must-have. On the other hand, if you’re simply trying to move around your home and locate EMF radiation sources, the audio feature is truly impressive. Using the audio output, you don’t even need to glance at the display. The Audio and Light buttons can be found in the battery compartment.
【Package List】 1 X EMF Meter ( 9V alkaline battery is not included ); 1 X user manual.